75 pound accumulator head blow molder, China accumulator head blow molder Supplier and Manufacturer

* CLAMP TONNAGE: 180 TONS
* EXTRUDER SIZE: 6 INCH DIAMETER, 24:1 L:D
* EXTRUDER DRIVE: 425HP DC
* SHOT SIZE: SINGLE HEAD, 75 POUNDS (32.8 kg)
* CONTROLS: BARBER COLEMAN MACO 8000
* 100 POINT PARISON PROGRAMMER
* 60 INCH WIDE X 84 INCH LONG CLEAR PLATEN
* AUTOMATIC PART TAKE-OUT FOR UNLIMITED PRESS ACCESS
* 4.5 to 26 inch tooling range
* 66 inch maximum clamp open daylight
* 10 inch minimum clamp closed daylight
* Vertical platen height adjustment +/- 4 inches
* Side to side platen adjustment +/- 3 inches
* Front to back platen adjustment +/- 3 inches
* Manual press shut height adjustment

Additional specifications of the accumulator head blow molder:
EXTRUDER SECTION:
* Continuous extrusion
* High performance feed screw with Colmonoy 56 hard surface flights
* Sterling barrel assembly fabricated of 4140 alloy steel with bimetallic inlay of Xaloy 102 or equivalent
and a bolt type front flange.
* Cast aluminum heaters with integral cooling coils.
* Closed loop cooling system.
* Rupture disk, pressure reducer and indicator.

ACCUMULATOR HEAD:
* First in, first out material flow
* Common shooting ring and six push rods
* One servo valve and DC transducer per head
* Individual control of flow (speed) of accumulator shooting with digital readout

CLAMP SECTION of the accumulator head blow molder:
* Relative platen speed 1200 inches per minute
* Mechanical adjustable stops to perform as movable guide rods

MICROPROCESSOR MACHINE CONTROL of the accumulator head blow molder:
* Maco 8000
* Lumitech electro luminescent Touch-Trol operator control station
Remote and accessible with swing-away feature
Set-up operation control buttons and switches
Ammeter, tachometer, and speed control for DC drive
Pressure indicator
* System/ Insta-set module
* Sequence module
* Five heat/cool module - six zones
* Temperature heat only modules - two 12-zones
* Linear positioning
* Multi-parameter process control speed for parison drop
* Pressure flow module
* Cabinet is provided with space for a maximum of 15 modules

MAIN ELECTRICAL CONTROL PANEL of the accumulator head blow molder:
* Three door construction
* Motor starter for main hydraulic AC motor
* Ammeters on each heater zone for heater burn-out detection
* Mercury contactors with circuit breakers on heater zones
* Isolation transformer for microprocessor
* Main disconnect switch
* DC drive controls
* Panel climate control devise
* Voltage regulator

MAIN BASE HOUSES of the accumulator head blow molder:
* Extruder
* Accumulator heads
* Hydraulic unit
* Control cabinet
* Press

PRIMARY POWER WIRING of the accumulator head blow molder:
- Maco 8000 is designed to operate from a 102-132 VAC, 50/60 Hz, single phase power source.
Each module contains its own power supply which provides all operating voltages for the module
circuitry. Control equipment should not be connected to power sources subject to extreme voltage
fluctuations caused by switching heavy loads. A voltage step-down isolation or voltage regulation
transformer installed in the control cabinet is supplied.

-----------------------------------

NOTE: Although machinery descriptions are believed to be accurate and
are from sources deemed reliable, they are not guaranteed and we
invite your inspection prior to purchase

75 pound accumulator head blow molding machine

Manufactures custom designed accumulator head blow molding systems for a range of packaging applications capable of processing PVC, polyolefins, and engineered thermoplastics.

Manufacturer of plastic blow molding machines and equipment, mold capacities from 20cc to 200 liters in PE, PP and PVC materials.

Specializing in building extrusion blow molds and designing and building of machine specific trim tooling.